. 000 - Action Codes and Responses
. 001- Announce Zone Name
. 004 - Start Entry Delay
. 005 - Cancel Entry Delay
. 006 - Exit Terminator
. 007 - Siren OFF
. 008 - All Outputs OFF
. 009 - Activate Door Station
. 010 - Unbypass All Zones
. 011 - CMS Dial Test
. 012 - Exit if Zero
. 013 - Exit Response if not Zero
. 014 - Skip To Marker unconditionally
. 015 - Skip to Marker if Zero
. 016 - Skip to Marker if Not Zero
. 017- Force Arm if Arming
. 020 - Require Engineer Reset to Re-arm
. 021- Skip Alarm
. 022 - Keypad Intercom Request
. 023 -Skip Announcement of Zone
. 024 - Echo Dialout on Keypad
. 025 - Do Engineer Reset
. 026 - Stop Door Station Ringer
. 028 - System Reset
. 029 - Announce Time
. 030 - Force Dialout
. 031 - Get Last Counter
. 064 - Activate Siren
. 065 - Bell On/Off
. 066 - Strobe Output On/Off
. 067 - Skip to Marker if Input = Value
. 068 - Skip to Marker if Input <> Value
. 069 - Skip to Marker if Input >= Value
. 070 - Skip to Marker if Input < Value
. 071 - Autoarm
. 072 - Key Arm
. 073 - Get Parameter
. 074 - Do Response
. 075 - Bypass Zone
. 076 - Unbypass Zone
. 077 - Get Output State
. 078 - Change Output State
. 079 - Get Input status
. 080 - Not Used
. 081 - Get Counter Value
. 082 - Start Battery Test
. 083 - Increment Counter
. 084 - Decrement Counter
. 085 - Stop Timer
. 086 - Check Timer
. 088 - Activate Alarm (Report User)
. 089 - Read Analog Input
. 090 - Switched Aux On/Off
. 091 - Keypad Menu Shortcut
. 092 - Engineer Code Enable/Disable
. 093- Baby Monitor Keypad
. 094 - Assign Keypad to Zone for Voice Station
. 095 - Call Screening On/Off
. 096 - Set Message Tag for Recording
. 097- Activate Reminder Message
. 098 - Daylight Saving Time adjust
. 099 - Set Authorization Code
. 100 - Limit Dialout
. 101 - Set Parameter
. 102- Do Alarm (Report Zone)
. 103, Load Counter with Input Value
. 104 - Subtract Counter from Input value
. 105 - AND Input with Input Value
. 106 - OR Input with Input Value
. 107 - XOR Input with Input Value
. 108 - Omit Input
. 109 - Set no of cycles for X10 Bright/dim command
. 110 - Check New Messages in User Mailbox
. 111- Start Door Station Timer
. 113 - Branch Unconditional
. 114 - Branch if =0
. 115 - Branch if <>0
. 128 - Output Action
. 129 - Send Infrared Signal from output
. 130 - Pulse Output
. 131 - Load Counter
. 132 - Flags Action
. 133 - Reminder Message on Keypad/Door Station
. 134- Shortcut to Keypad Menu and Selection
. 135 - Record Message on Door Station
. 136 - Set Virtual Output
. 138 - UCM Dial Up command
. 139 - Keypad Announcements On/off
. 140 - X10 Extended Command
. 142 - Branch if >= Parameter 1
. 143 - Branch if < Parameter 1
. 144 -Exit if = or <> or < or >= parameter2
. 145 - Branch if = Parameter 1
. 146 - Branch if <> Parameter 1
. 192 - Marker
. 193 - Exit Response
. 194 - Start Timer
. 197 - Send Data to RS232
. 198 - Copy Counter to Counter(s)
. 199 - Announce Words